Search results

This paper aims to report on the physical distortions associated with the use of additive manufactured components for wind tunnel testing and procedures adopted to correct for them.

Wings of a joined-wing test aircraft configuration were fabricated with additive manufacturing and tested in a subsonic closed-loop wind tunnel. Wing deflections were observed during testing and quantified using image-processing procedures. These quantified deflections were then incorporated into numerical simulations and results had agreed with wind tunnel measurement results.

Additive manufacturing provides cost-effective wing components for wind tunnel test components with fast turn-around time. They can be used with confidence if the wing deflections could be accounted for systematically and accurately, especially at the region of aerodynamic stall.

Significant wing flutter and unsteady deflections were encountered at higher test velocities and pitch angles. This reduced the accuracy in which the wing deflections could be corrected. Additionally, wing twists could not be quantified as effectively because of camera perspectives.

This paper shows that additive manufacturing can be used to fabricate aircraft test components with satisfactory strength and quantifiable deflections for wind tunnel testing, especially when the designs are significantly complex and thin.

The purpose of this paper is to evaluate the impact of different Additive Manufacturing (AM) orientations on the structural behavior of topologically optimized wings for Unmanned Aerial Systems (UAS), which might enable lightweight and low cost, yet complex, wing structural designs.

Based on an aerodynamic load, a two dimensional NACA0012 airfoil is topologically optimized considering PolyLatic Acid (PLA), several volume fractions and different manufacturing orientations. Then, the resulting topologies are post-processed to allow for manufacturing and extrude to three dimensional wing geometries with constant cross-sections. These wings are then manufactured using Fusion Deposition Modeling (FDM) technology and their dynamic structural behavior analyzed by means of Experimental Modal Analysis (EMA) in the linear elastic region.

Volume fraction increase is observed to improve the structural performance without increasing the manufacturing time. Despite manufacturing the wing from the leading edge to the trailing edge can reduce manufacturing time using FDM technology, it is found to be more difficult to build.

This research is a contribution toward the design and built of lightweight and low cost wings for UAS.

The purpose of this paper is to propose a new approach of using additively manufactured parametric models in the wind tunnel test-based aerodynamic shape optimization (ASO) framework and to present its applicability test results obtained from a realistic aircraft design problem.

For aircraft shape optimization, the following three methodologies were used. First, as a validation study, the possibility of using rapid prototyping (RP) model in the wind tunnel test was verified. Second, through the wind tunnel test-based ASO, the application and feasibility of the real fighter aircraft shape optimization were verified. A generic fighter configuration is parameterized to generate various test models using additive manufacturing. Wind tunnel tests are conducted to measure their stability criteria in high angle of attack (AOA). Finally, a computational fluid dynamics (CFD) study was performed and analysis procedures, costs and results compared to the wind tunnel test were compared and reviewed.

RP technology can significantly reduce the time and cost of generating parametric wind tunnel models and can open up new possibilities for wind tunnel tests to be used in the rigorous aerodynamic design loop. There was a slight difference between the results of the RP model and the metallic model because of rigidity and surface roughness. However, the tendency of the aerodynamic characteristics was very similarly predictable. Although there are limitations to obtaining precise aerodynamic data, it is a suitable method to be applied to comparative studies on various shapes with large geo-metric changes in the early phase of design. The CFD analysis indicates that the wind tunnel-based ASO using the RP model shows the efficiency corresponding to the CFD shape optimization.

The RP parametric models may have various assembly error sources and rigidity problems. The proposed methodology may not be suitable for collecting the accurate aerodynamic database of a final design; rather, the methodology is more suitable to screen out many configurations having fairly large shape variation in the early stage of the design process.

The wind tunnel test-based ASO can replace or supplement CFD-based ASO. In areas where CFD accuracy is low, such as high AOA flight characteristics, RP model wind tunnel-based ASO can be a research method that can secure both efficiency and accuracy advantages, providing ten times more effective in terms of cost and time. The wind tunnel test is used to obtain aerodynamic data at the final stage of shape design. It can be extended to a comparative study of several shapes in the early design phase. This procedure can be applied for both industrial level and educational aircraft design activities.

This study is the application to be applied as a parametric study on the whole aircraft, rather than using the RP model applying a simple partial control surface or configuration change of a part of the wing. The possibility of using the RP model was confirmed by comparing and verifying each other in a medium-sized wind tunnel using a relatively large RP model and a metallic model. It was verified that it can be applied in the shape design process, not the shape verification in the traditional design procedure, and a comparison with the CFD method was also performed. With further development and validation efforts, the new design framework may become an industrial standard for future aircraft development.

The purpose of this paper is to establish a methodology for the design and development of patient-specific elbow implant with an elastic modulus close to that of the human bone. One of the most preferred implant material is titanium alloy which is about 8 to 9 times higher in strength than that of the human bone and is the closest than other metallic biomedical materials.

The methodology begins with the design of the implant from patient-specific computed tomography information and incorporates the manufacturing of the implant via a novel rapid prototyping assisted microwave sintering process.

The elastic modulus and the flexural strength of the implant were observed to be comparable to that of human elbow bones. The fatigue test depicts that the implant survives the one million cycles under physiological loading conditions. Other mechanical properties such as impact energy absorption, hardness and life cycle tests were also evaluated. The implant surface promotes human cell growth and adhesion and does not cause any adverse or undesired effects i.e. no cytotoxicity.

Stress shielding, and therefore, aseptic loosening of the implant shall be avoided. In the event of any trauma post-implantation, the implant would not hurt the patient.

The present study describes a methodology for the first time to be able to obtain the strength required for the medical implant without sacrificing the fatigue life requirement.

Information and communications technology (ICT) offers enormous opportunities for individuals, businesses and society. The application of ICT is equally important to economic and non-economic activities. Researchers have increasingly focused on the adoption and use of ICT by small and medium enterprises (SMEs) as the economic development of a country is largely dependent on them. Following the success of ICT utilisation in SMEs in developed countries, many developing countries are looking to utilise the potential of the technology to develop SMEs. Past studies have shown that the contribution of ICT to the performance of SMEs is not clear and certain. Thus, it is crucial to determine the effectiveness of ICT in generating firm performance since this has implications for SMEs’ expenditure on the technology. This research examines the diffusion of ICT among SMEs with respect to the typical stages from innovation adoption to post-adoption, by analysing the actual usage of ICT and value creation. The mediating effects of integration and utilisation on SME performance are also studied. Grounded in the innovation diffusion literature, institutional theory and resource-based theory, this study has developed a comprehensive integrated research model focused on the research objectives. Following a positivist research paradigm, this study employs a mixed-method research approach. A preliminary conceptual framework is developed through an extensive literature review and is refined by results from an in-depth field study. During the field study, a total of 11 SME owners or decision-makers were interviewed. The recorded interviews were transcribed and analysed using NVivo 10 to refine the model to develop the research hypotheses. The final research model is composed of 30 first-order and five higher-order constructs which involve both reflective and formative measures. Partial least squares-based structural equation modelling (PLS-SEM) is employed to test the theoretical model with a cross-sectional data set of 282 SMEs in Bangladesh. Survey data were collected using a structured questionnaire issued to SMEs selected by applying a stratified random sampling technique. The structural equation modelling utilises a two-step procedure of data analysis. Prior to estimating the structural model, the measurement model is examined for construct validity of the study variables (i.e. convergent and discriminant validity).

The estimates show cognitive evaluation as an important antecedent for expectation which is shaped primarily by the entrepreneurs’ beliefs (perception) and also influenced by the owners’ innovativeness and culture. Culture further influences expectation. The study finds that facilitating condition, environmental pressure and country readiness are important antecedents of expectation and ICT use. The results also reveal that integration and the degree of ICT utilisation significantly affect SMEs’ performance. Surprisingly, the findings do not reveal any significant impact of ICT usage on performance which apparently suggests the possibility of the ICT productivity paradox. However, the analysis finally proves the non-existence of the paradox by demonstrating the mediating role of ICT integration and degree of utilisation explain the influence of information technology (IT) usage on firm performance which is consistent with the resource-based theory. The results suggest that the use of ICT can enhance SMEs’ performance if the technology is integrated and properly utilised. SME owners or managers, interested stakeholders and policy makers may follow the study’s outcomes and focus on ICT integration and degree of utilisation with a view to attaining superior organisational performance.

This study urges concerned business enterprises and government to look at the environmental and cultural factors with a view to achieving ICT usage success in terms of enhanced firm performance. In particular, improving organisational practices and procedures by eliminating the traditional power distance inside organisations and implementing necessary rules and regulations are important actions for managing environmental and cultural uncertainties. The application of a Bengali user interface may help to ensure the productivity of ICT use by SMEs in Bangladesh. Establishing a favourable national technology infrastructure and legal environment may contribute positively to improving the overall situation. This study also suggests some changes and modifications in the country’s existing policies and strategies. The government and policy makers should undertake mass promotional programs to disseminate information about the various uses of computers and their contribution in developing better organisational performance. Organising specialised training programs for SME capacity building may succeed in attaining the motivation for SMEs to use ICT. Ensuring easy access to the technology by providing loans, grants and subsidies is important. Various stakeholders, partners and related organisations should come forward to support government policies and priorities in order to ensure the productive use of ICT among SMEs which finally will help to foster Bangladesh’s economic development.

Citizens are substantial stakeholders in every e-government system, thus their willingness to use and ability to access the system are critical. Unequal access and information and communication technology usage, which is known as digital divide, however has been identified as one of the major obstacles to the implementation of e-government system. As digital divide inhibits citizen’s acceptance to e-government, it should be overcome despite the lack of deep theoretical understanding on this issue. This research aimed to investigate the digital divide and its direct impact on e-government system success of local governments in Indonesia as well as indirect impact through the mediation role of trust. In order to get a comprehensive understanding of digital divide, this study introduced a new type of digital divide, the innovativeness divide.

The research problems were approached by applying two-stage sequential mixed method research approach comprising of both qualitative and quantitative studies. In the first phase, an initial research model was proposed based on a literature review. Semi-structured interview with 12 users of e-government systems was then conducted to explore and enhance this initial research model. Data collected in this phase were analyzed with a two-stage content analysis approach and the initial model was then amended based on the findings. As a result, a comprehensive research model with 16 hypotheses was proposed for examination in the second phase.

In the second phase, quantitative method was applied. A questionnaire was developed based on findings in the first phase. A pilot study was conducted to refine the questionnaire, which was then distributed in a national survey resulting in 237 useable responses. Data collected in this phase were analyzed using Partial Least Square based Structural Equation Modeling.

The results of quantitative analysis confirmed 13 hypotheses. All direct influences of the variables of digital divide on e-government system success were supported. The mediating effects of trust in e-government in the relationship between capability divide and e-government system success as well as in the relationship between innovativeness divide and e-government system success were supported, but was rejected in the relationship between access divide and e-government system success. Furthermore, the results supported the moderating effects of demographic variables of age, residential place, and education.

This research has both theoretical and practical contributions. The study contributes to the developments of literature on digital divide and e-government by providing a more comprehensive framework, and also to the implementation of e-government by local governments and the improvement of e-government Readiness Index of Indonesia.

The strategic management literature emphasizes the concept of business intelligence (BI) as an essential competitive tool. Yet the sustainability of the firms’ competitive advantage provided by BI capability is not well researched. To fill this gap, this study attempts to develop a model for successful BI deployment and empirically examines the association between BI deployment and sustainable competitive advantage. Taking the telecommunications industry in Malaysia as a case example, the research particularly focuses on the influencing perceptions held by telecommunications decision makers and executives on factors that impact successful BI deployment. The research further investigates the relationship between successful BI deployment and sustainable competitive advantage of the telecommunications organizations. Another important aim of this study is to determine the effect of moderating factors such as organization culture, business strategy, and use of BI tools on BI deployment and the sustainability of firm’s competitive advantage.

This research uses combination of resource-based theory and diffusion of innovation (DOI) theory to examine BI success and its relationship with firm’s sustainability. The research adopts the positivist paradigm and a two-phase sequential mixed method consisting of qualitative and quantitative approaches are employed. A tentative research model is developed first based on extensive literature review. The chapter presents a qualitative field study to fine tune the initial research model. Findings from the qualitative method are also used to develop measures and instruments for the next phase of quantitative method. The study includes a survey study with sample of business analysts and decision makers in telecommunications firms and is analyzed by partial least square-based structural equation modeling.

The findings reveal that some internal resources of the organizations such as BI governance and the perceptions of BI’s characteristics influence the successful deployment of BI. Organizations that practice good BI governance with strong moral and financial support from upper management have an opportunity to realize the dream of having successful BI initiatives in place. The scope of BI governance includes providing sufficient support and commitment in BI funding and implementation, laying out proper BI infrastructure and staffing and establishing a corporate-wide policy and procedures regarding BI. The perceptions about the characteristics of BI such as its relative advantage, complexity, compatibility, and observability are also significant in ensuring BI success. The most important results of this study indicated that with BI successfully deployed, executives would use the knowledge provided for their necessary actions in sustaining the organizations’ competitive advantage in terms of economics, social, and environmental issues.

This study contributes significantly to the existing literature that will assist future BI researchers especially in achieving sustainable competitive advantage. In particular, the model will help practitioners to consider the resources that they are likely to consider when deploying BI. Finally, the applications of this study can be extended through further adaptation in other industries and various geographic contexts.

The purpose of this paper is to enhance the anticorrosion property of aluminium pigments and to improve their compatibility with polymers in coating.

Aluminium pigments encapsulated by organic‐inorganic layer were prepared by hydrolysis and condensation of organic silane acrylate resin and tetraethoxy silane (TEOS) on the surface of pigments via sol‐gel method. TEOS and poly (methyl methacryalte‐n‐butyl acrylate‐vinyl triethoxysilane) (PMBV) formed in advance by co‐polymerisation of methyl methacrylate (MMA), n‐butyl acrylate (BA) and vinyl triethoxysilane (VTES) were used as precursors. The adhesion property of the aluminium pigments was measured by peel test, and the loss of silvery appearance after encapsulation and acid soaking were both evaluated by colour lightness difference (ΔL) measurement. The encapsulated aluminium pigments were further characterised by means of FTIR, SEM, TG and XPS.

It was found that PMBV‐SiO2 thin films could be formed on the surface of aluminium pigments smoothly and uniformly, and the adhesion and anticorrosion performances of encapsulated aluminium pigments were improved significantly.

The organic silane acrylate resin used as a precursor in the sol‐gel process could be synthesised from other aclyate monomers. In addition, the hydrolysis and condensation mechanism of organic silane acrylate resin on the surface of aluminium pigments need further studies.

The method developed provided a good solution to the two problems of aluminium pigments and increased their application values.

The method of improving adhesion and anticorrosion properties of aluminium pigments was novel and could find numerous applications in surface coatings and adhesives.

There is significant amount of literature tackling different issues related to the port industry. The present chapter focuses on a single business unit of seaports aiming at the documentation of works related to container terminals.

An effort to review, collect and present the majority of the works present in the last 30 years, between 1980 and 2010, has been made in order to picture the problems dealt and methods used by the authors in the specific research field. To facilitate the reader, studies have been grouped under five categories of addressed problems (productivity and competitiveness, yard and equipment utilization, equipment scheduling, berth planning, loading/unloading) and four modelling methodologies (mathematics and operations research, management and economics, simulation, stochastic modelling).

The analysis shows that most works focus on productivity and competitiveness issues followed by yard and equipment utilisation and equipment scheduling. In reference to the methodologies used managerial and economic approaches lead, followed by mathematics and operations research.

In reference to future research, two fields have been identified where there is scope of significant contribution by the academic community: container terminal security and container terminal supply chain integration.

The present chapter provides the framework for researchers in the field of port container terminals to picture the so far works in this research area and enables the identification of gaps at both research question and methodology level for further research.

Modern mathematicians and scientists of math-related disciplines often use Document Preparation Systems (DPS) to write and Computer Algebra Systems (CAS) to calculate mathematical expressions. Usually, they translate the expressions manually between DPS and CAS. This process is time-consuming and error-prone. The purpose of this paper is to automate this translation. This paper uses Maple and Mathematica as the CAS, and LaTeX as the DPS.

Bruce Miller at the National Institute of Standards and Technology (NIST) developed a collection of special LaTeX macros that create links from mathematical symbols to their definitions in the NIST Digital Library of Mathematical Functions (DLMF). The authors are using these macros to perform rule-based translations between the formulae in the DLMF and CAS. Moreover, the authors develop software to ease the creation of new rules and to discover inconsistencies.

The authors created 396 mappings and translated 58.8 percent of DLMF formulae (2,405 expressions) successfully between Maple and DLMF. For a significant percentage, the special function definitions in Maple and the DLMF were different. An atomic symbol in one system maps to a composite expression in the other system. The translator was also successfully used for automatic verification of mathematical online compendia and CAS. The evaluation techniques discovered two errors in the DLMF and one defect in Maple.

This paper introduces the first translation tool for special functions between LaTeX and CAS. The approach improves error-prone manual translations and can be used to verify mathematical online compendia and CAS.